https://doi.org/10.25198/2077-7175-2020-6-163
IMPROVEMENT OF THE TECHNOLOGY FOR CONTROLLING THE PARAMETERS OF THE LUBRICATING SYSTEM OF THE D-245 DIESEL ENGINE
S. V. Timokhin
Penza State Agrarian University, Penza, Russia
e-mail: timohinsv@gmail.com
Y. V. Rodionov
Penza State University of Architecture and Construction, Penza, Russia
e-mail: dekauto@pguas.ru
I. I. Kurbakov
National research Mordovian State University named after N. P. Ogarev, Saransk, Russia
e-mail: mrsu2@mail.ru
Abstract. А significant factor affecting the reliability of the internal combustion engine and its technical and Economic indicators is the efficiency of the lubrication system. When the standard oil supply is applied, semiliquid friction occurs between the contacting parts, in which the parts are not completely separated by a layer of oil. However, with this friction, the required durability of components and parts with heat removal is guaranteed. The performance of the engine lubrication system is determined by the state of its elements (coarse and fine filters, oil radiator and pump, valves), as well as the quality of oil, its level in the internal combustion engine crankcase and temperature. In domestic internal combustion engines, the minimum oil level in the crankcase is controlled, but in operation there are situations when the oil level exceeds its maximum permissible value. This situation occurs when coolant or fuel enters the lubrication system. Coolant can get into the oil if the cylinder head gaskets, sleeve o-rings, or cracks in the cylinder head and block are broken. Top-Livo can enter the oil through worn and damaged parts of the fuel equipment (gas pump diaphragm, fuel pump plunger pairs, etc.). These liquids sharply degrade the quality of the oil and increase the wear of internal combustion engine parts, and the standard singlelevel indicator will not give the driver operational information about the malfunction.
In connection with the above, the purpose of this work is to improve the technology for monitoring the technical condition of the internal combustion engine lubrication system on the example of the d-245 diesel engine and its modifications, which are widely used in GAZ (GAZ-3309), ZIL (ZIL-5301), MAZ (MAZ Zubrenok), PAZ buses (PAZ-3205), MTZ tractors (MTZ — 100, 892, 1020), agricultural and construction equipment.by developing and implementing a built — in device for monitoring the minimum and maximum oil levels in the crankcase, as well as its temperature. The scientific novelty of the work is due to the use of new circuit and technical solutions, as well as the original algorithm of the sensor operation developed by the authors, based on the use of switching laws of reed switches with normally closed and normally open contacts, the operation of which is spaced over time and controlled oil levels.
Block diagram of the proposed device comprises a multifunction sensor level and oil temperature, including sensors of the mi-minimum and increased levels of engine oil in the crankcase of the engine and its temperature, the operation mode switch signal cooling temperature-edusei fluid and engine oil, the first and second voltage сomparators, indicator lights, buzzer, switch power supply, voltage regulator and regular temperature sensor coolant.
The use of the developed device significantly increases the reliability and convenience of monitoring one of the most important indicators of internal combustion engines-the oil level in the crankcase, which will avoid significant engine damage.
As a result of further research, it is planned to develop the device design, conduct laboratory studies of the developed multifunctional sensor in order to determine the dependence of its resistance on the temperature at the normal level of engine oil in the measuring flask, as well as determine the actual values of the developed sensor response heights at the lower and upper levels.
Key words: oil level monitoring, maintenance, lubrication system, block diagram, diesel.
Cite as: Timokhin, S. V., Rodionov, Yu. V., Kurbakov, I. I. (2020) [Improvement of the technology for controlling the parameters of the lubricating system of the D-245 diesel engine]. Intellekt. Innovatsii. Investitsii [Intellect. Innovations. Investments]. Vol. 6, рр. 163–171. DOI: 10.25198/2077-7175-2020-6-163.
